Products
Solutions
Partners
Support
Company
Try Now
Pulse Secure Community
Help
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 

Dial up VPN, Shrew and Close - AGE OUT policy....

LeoT_
Not applicable
‎02-23-2010 01:07:AM
‎02-23-2010 01:07:AM

Dial up VPN, Shrew and Close - AGE OUT policy....

Hi,

I have a VPN between a SSG5 and a Shrewsoft VPN Client.

VPN is correctly build up, I can ping the trust interface but i can't ping the server.

Maybe a routing problem?

Consider that i have a VLAN on Video (5) zone and I can ping 10.70.7.218 (SSG5 interface in Video(5) ).

The policy give me this report:

2010-02-23 09:55:38172.16.0.1:5772610.70.7.150:53172.16.0.1:5772610.70.7.150:53DNS63 sec.1580Close - AGE OUT
2010-02-23 09:54:05172.16.0.1:6314110.70.7.150:53172.16.0.1:6314110.70.7.150:53DNS62 sec.3280Close - AGE OUT
2010-02-23 09:54:03172.16.0.1:6318210.70.7.150:53172.16.0.1:6318210.70.7.150:53DNS60 sec.1500Close - AGE OUT

This is my config file:

set clock timezone 0
set vrouter trust-vr sharable
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
unset auto-route-export
exit
set alg appleichat enable
unset alg appleichat re-assembly enable
set alg sctp enable
set auth-server "Local" id 0
set auth-server "Local" server-name "Local"
set auth default auth server "Local"
set auth radius accounting port 1646
set admin name "admin"
set admin password "xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx"
set admin auth web timeout 10
set admin auth dial-in timeout 3
set admin auth server "Local"
set admin format dos
set zone "Trust" vrouter "trust-vr"
set zone "Untrust" vrouter "trust-vr"
set zone "DMZ" vrouter "trust-vr"
set zone "VLAN" vrouter "trust-vr"
set zone id 100 "Video (5)"
set zone "Untrust-Tun" vrouter "trust-vr"
set zone id 101 "vpn_client" tunnel Video (5)
set zone "vpn_client" vrouter "untrust-vr"
set zone "Trust" tcp-rst
set zone "Untrust" block
unset zone "Untrust" tcp-rst
set zone "MGT" block
set zone "DMZ" tcp-rst
set zone "VLAN" block
unset zone "VLAN" tcp-rst
unset zone "Video (5)" tcp-rst
set zone "Untrust" screen tear-drop
set zone "Untrust" screen syn-flood
set zone "Untrust" screen ping-death
set zone "Untrust" screen ip-filter-src
set zone "Untrust" screen land
set zone "V1-Untrust" screen tear-drop
set zone "V1-Untrust" screen syn-flood
set zone "V1-Untrust" screen ping-death
set zone "V1-Untrust" screen ip-filter-src
set zone "V1-Untrust" screen land
set interface "ethernet0/0" zone "Untrust"
set interface "ethernet0/1" zone "DMZ"
set interface "bgroup0" zone "Trust"
set interface "bgroup1" zone "Video (5)"
set interface bgroup0 port ethernet0/2
set interface bgroup1 port ethernet0/5
unset interface vlan1 ip
set interface ethernet0/0 ip 83.0.0..180/24
set interface ethernet0/0 route
set interface bgroup0 ip 192.168.10.218/24
set interface bgroup0 nat
set interface bgroup1 ip 10.70.7.218/24
set interface bgroup1 route
set interface ethernet0/0 gateway 83.0.0..177
unset interface vlan1 bypass-others-ipsec
unset interface vlan1 bypass-non-ip
set interface ethernet0/0 ip manageable
set interface bgroup0 ip manageable
set interface bgroup1 ip manageable
set interface ethernet0/0 manage ping
set interface ethernet0/0 manage web
set interface bgroup0 manage mtrace
set interface bgroup1 manage ping
set interface bgroup1 manage web
set interface "serial0/0" modem settings "USR" init "AT&F"
set interface "serial0/0" modem settings "USR" active
set interface "serial0/0" modem speed 115200
set interface "serial0/0" modem retry 3
set interface "serial0/0" modem interval 10
set interface "serial0/0" modem idle-time 10
set flow tcp-mss
unset flow tcp-syn-check
unset flow tcp-syn-bit-check
set flow reverse-route clear-text prefer
set flow reverse-route tunnel always
set pki authority default scep mode "auto"
set pki x509 default cert-path partial
set address "Trust" "10.70.0.0/255.255.0.0" 10.70.0.0 255.255.0.0
set address "Trust" "10.70.7.0/24" 10.70.7.0 255.255.255.0
set address "Trust" "Video rete" 10.70.7.0 255.255.255.0
set address "Trust" "Video server" 10.70.7.150 255.255.255.255
set address "Video (5)" "10.70.7.0/24" 10.70.7.0 255.255.255.0
set address "Video (5)" "10.70.7.150/32" 10.70.7.150 255.255.255.255
set ippool "vpn_ippool" 10.0.0.1 10.0.0.10
set ippool "ippool_vpn" 172.16.0.1 172.16.0.20
set user "leo" uid 10
set user "leo" type xauth
set user "leo" remote ippool "ippool_vpn"
set user "leo" remote dns1 "10.70.7.150"
set user "leo" password "yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy"
unset user "leo" type auth
set user "leo" "enable"
set user "vpnclient_phase1_id" uid 9
set user "vpnclient_phase1_id" ike-id fqdn "client.gigli" share-limit 1
set user "vpnclient_phase1_id" type ike
set user "vpnclient_phase1_id" "enable"
set user-group "vpnclient_group" id 4
set user-group "vpnclient_group" user "leo"
set user-group "vpnclient_group" user "vpnclient_phase1_id"
set ike gateway "vpnclient_gateway" dialup "vpnclient_group" Aggr local-id "vpngw.gigli" outgoing-interface "ethernet0/0" preshare "zzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz" proposal "pre-g2-3des-sha" "pre-g2-3des-md5" "pre-g2-aes128-sha" "pre-g2-aes128-md5"
set ike gateway "vpnclient_gateway" dpd-liveness interval 30
unset ike gateway "vpnclient_gateway" nat-traversal udp-checksum
set ike gateway "vpnclient_gateway" nat-traversal keepalive-frequency 5
set ike gateway "vpnclient_gateway" xauth server "Local"
unset ike gateway "vpnclient_gateway" xauth do-edipi-auth
set ike respond-bad-spi 1
set ike ikev2 ike-sa-soft-lifetime 60
unset ike ikeid-enumeration
unset ike dos-protection
unset ipsec access-session enable
set ipsec access-session maximum 5000
set ipsec access-session upper-threshold 0
set ipsec access-session lower-threshold 0
set ipsec access-session dead-p2-sa-timeout 0
unset ipsec access-session log-error
unset ipsec access-session info-exch-connected
unset ipsec access-session use-error-log
set xauth default ippool "ippool_vpn"
set xauth default dns1 10.70.7.150
set vpn "vpnclient_tunnel" gateway "vpnclient_gateway" replay tunnel idletime 0 proposal "nopfs-esp-3des-sha" "nopfs-esp-3des-md5" "nopfs-esp-aes128-sha" "nopfs-esp-aes128-md5"
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
exit
set url protocol websense
exit
set policy id 2 from "Untrust" to "Video (5)" "Dial-Up VPN" "10.70.7.0/24" "ANY" tunnel vpn "vpnclient_tunnel" id 0x9 pair-policy 5 log
set policy id 2
exit
set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit log
set policy id 1
exit
set policy id 5 from "Video (5)" to "Untrust" "10.70.7.0/24" "Dial-Up VPN" "ANY" tunnel vpn "vpnclient_tunnel" id 0x9 pair-policy 2 log
set policy id 5
exit
set nsmgmt bulkcli reboot-timeout 60
set ssh version v2
set config lock timeout 5
unset license-key auto-update
set snmp port listen 161
set snmp port trap 162
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
unset add-default-route
exit
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
exit

This is the report:

2010-02-23 10:01:18infoIKE 82.0.0.149 Phase 2 msg ID 9c8df9fe: Completed negotiations with SPI b32b6823, tunnel ID 32775, and lifetime 3600 seconds/0 KB.
2010-02-23 10:01:18infoIKE 82.0.0.149 Phase 2 msg ID 9c8df9fe: Responded to the peer's first message.
2010-02-23 10:01:05infoIKE 82.0.0.149: XAuth login was passed for gateway vpnclient_gateway, username leo, retry: 0, Client IP Addr 172.16.0.1, IPPool name: ippool_vpn, Session-Timeout: 0s, Idle-Timeout: 0s.
2010-02-23 10:01:05infoIKE 82.0.0.149: XAuth login was refreshed for username leo at 172.16.0.1/255.255.255.255.
2010-02-23 10:01:05infoRejected an IKE packet on ethernet0/0 from 82.0.0.149:5916 to 83.0.0.180:4500 with cookies b055e36ced0c7ad5 and 0f3abbb6fc5fdbbc because A Phase 2 packet arrived while XAuth was still pending.
2010-02-23 10:01:05infoIKE 82.0.0.149 Phase 1: Completed Aggressive mode negotiations with a 28800-second lifetime.
2010-02-23 10:01:05infoIKE 82.0.0.149 Phase 1: Completed for user vpnclient_phase1_id.
2010-02-23 10:01:05infoIKE<82.0.0.149> Phase 1: IKE responder has detected NAT in front of the remote device.
2010-02-23 10:01:05infoIKE<82.0.0.149> Phase 1: IKE responder has detected NAT in front of the local device.
2010-02-23 10:01:05infoIKE 82.0.0.149 Phase 1: Responder starts AGGRESSIVE mode negotiations.
2010-02-23 10:01:02notifAll logged events or alarms were cleared by admin admin

Routing table:

IP/Netmask Gateway Interface Protocol Preference Metric Vsys Configure
trust-vr
*83.0.0.0/24 ethernet0/0C Root -
*83.0.0.180/32 ethernet0/0H Root -
192.168.10.0/24 bgroup0C Root -
192.168.10.218/32 bgroup0H Root -
*10.70.7.0/24 bgroup1C Root -
*10.70.7.218/32 bgroup1H Root -
*0.0.0.0/083.0.0.177ethernet0/0C 1Root -
0 Kudos
1 REPLY 1
Mrkool_
Super Contributor
‎02-23-2010 10:31:AM
‎02-23-2010 10:31:AM

Re: Dial up VPN, Shrew and Close - AGE OUT policy....

i think this is not the right forum for this you might want to ask this question in the Firewall section

0 Kudos
© 2017 Pulse Secure, LLC. Use of this website assumes acceptance of our Legal Notices and Privacy Policy. Pulse Secure has updated its Privacy Policy effective June 28, 2017.