- Pulse Secure Community
- :
- About firewall72_
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
since
10-29-2017
10-29-2017
firewall72_
Frequent Contributor
142
Posts
0
Kudos
8
Solutions
03-30-2012
09:17:AM
Hi, Does anyone know if it's possible to either import or push from a stand along SA2500 to a MAG4610 Cluster? Both are runnning 7.1R7. Tried a few different options, but nothing is taking. Not much log data to run with either. Any feedback and/or recommendations would be helpful. Thank you.
... View more
03-28-2012
08:08:AM
How many active users are on the box? What is your current license?
... View more
03-26-2012
11:59:AM
Hi, Does anyone know if it's possible to use cached AD credentials to authenticate via Pulse? My client is looking to use Location Awarenes to start/stop Pulse, which is working, but also wants to know if he could get around the login. I have the AD Authentication working, but wasn't sure about the SSO w/ Cached Credentials. Thank you.
... View more
03-14-2012
05:38:PM
Hi, We have a MAC 4610 running 7.1x with a full ICE license. Our business has decided to cluster (Active/Passive) this box and was wondering how the ICE license is handled. Do we need an additional ICE License for the Passive Node? My vendor is telling me we need two (one for each box), which goes against the standard licenses of being shared. I've gone through a bunch of KB's, forums and sites, but still haven't found my answer. Thank you!
... View more
01-31-2012
05:48:AM
Hi, It's a check box in the Profile. Go to Users, Resource Policies, Network Connect, Connection Profiles. Edit your Profile under Connect Settings, Transport and check the box for "Compression". I hope this helps.
... View more
01-26-2012
05:24:PM
Hi, Yes, you can cluster two boxes. However, I believe you need an external load balancer for Active/Active. Active/Passive, no load balancer. I hope this helps.
... View more
01-26-2012
05:18:PM
Hi, I've been using Cisco CUPC (8.6) and Jabber (Beta for the Mac) with SA 7.x Pulse/NC without issue. However, my Cisco VoIP Engineers don't use a Mac to setup softphones. I beleive they register these to AD usernames in each profile. I can find out more if needed.
... View more
01-26-2012
04:36:PM
Hi, You can also use trace-route. Traffic being routed via the Virtual Adapter (i.e. 10.200.200.1) will be encrypted, traffic routing via your local gateway will be sent in clear text.
... View more
11-07-2011
04:26:PM
Hi, If you can RDP to them internally, there are a few things to check. First, are you using Network Connect and the local RDP client or the Juniper RDP client (Terminal Services Bookmark)? I would make sure there is a policy for the resources you're trying to RDP to. Check "Users, Resource Policies, Network Connect or Terminal Services". Make sure you have an Access Policy for the resources (i.e. 192.168.1.0/24:3389) and apply it to the proper role.
... View more
11-01-2011
05:34:PM
Hi, Does this help? "The JSAM applet works by creating a mapping the FQDN of the server to a loopback IP (127.0.x.x). When the user attempts to connect, the local IP is returned for the resolution" = KB19776. So when the app stream is redirected to the loopback IP, JSAM will then route the traffic via the SSL tunnel for delivery to the SA/Server.
... View more
10-24-2011
06:57:PM
Hi, This should help. https://forums.pulsesecure.net/topic/pulse-connect-secure/111122-ive-cluster-license-change/highlight/true#M12355
... View more
10-19-2011
01:52:AM
Hi, I have a customer with a custom sign-in page that use Swivel PINsafe two factor authentication. It works on both 6.5R7 and 7.1R4 without issue. However, the new box with "Pulse" defined in the Role doesn't provide the custom login page. It appears it's being overriden on the client with a generic username and password. In 6.5R7, it provides the proper login page, which I believe is related to Network Connect being defined (Pulse works well). Has anyone come across a similar issue? To help simplify my question, is anyone using custom login pages with Pulse in 7.1? Thank you.
... View more
10-05-2011
04:49:PM
Hi, The current ESAP is 1-7-6. I would upload the latest ESAP and make it active. I would also double check the settings I mentioned earlier.
... View more
10-04-2011
08:39:PM
Hi, I would check to make sure you have enabled "Auto-update virus signature list" (Endpoing Security, Virus Signature Version Monitoring). I believe you will need to add your Juniper account details as well. If you haven't done so already, I would also make sure you're using the most recent ESAP. I hope this helps.
... View more
09-28-2011
07:57:AM
Hi, I would try copying the cert into a text file and save it with the .cer extension. Then import into the SA. Be sure to copy the "begin..." and "end..." rows as well.
... View more
09-26-2011
08:30:AM
Hi Tim, Go to System, Network, Overview and change the Hostname field. Save the config, then check the Maintenance, System page to verify the change was applied. I hope this helps.
... View more
09-06-2011
04:37:PM
Hi John, It may be related to the use of Roaming Profiles. This KB may help. Good luck. http://kb.pulsesecure.net/InfoCenter/index?page=content&id=KB21428&actp=search&viewlocale=en_US&searchid=1315351970399#_
... View more
08-04-2011
07:23:PM
Hi, Unless I'm missing something, your Contractors are using an external SA, yes? I would simply modify the ACL being used for WCCP and permit them direct-to-net. I don't see the need to proxy them for their own SSL VPN proxy.
... View more
07-08-2011
11:19:PM
Hi, I recall running into a similar issue a while back. I would check to make sure your vlan's are defined with the correct VLAN ID, IP and Mask in System, Network, VLAN. I would then double-check the VLAN assignment within the Role. Then test to make sure that VLAN can ping other resources on that subnet from the SA. If this test fails, you may have an issue with the trunk. Try Maintenance, Troubleshooting, Tools, Commands, Ping. Add an IP on that subnet and source it from VLAN 101. If this fails, please share your trunk config. I hope this helps. John
... View more
06-30-2011
07:41:PM
Hello, Does anyone have an update on the Mac/Pulse dilemma? In my perfect world, vendors release software for both Mac and Windows at the same time. Most of my clients are in mixed mode. It's been quite some time since I've come across a Windows Only shop. Thanks. John
... View more
06-28-2011
07:23:PM
Hi, Does anyone know or a JumpStation for the SA/MAG like there is for the SRX? http://kb.pulsesecure.net/InfoCenter/index?page=content&id=KB15694&smlogin=true_ Thank you. John
... View more
06-02-2011
06:55:PM
Hi, You typically wouldn't use the SA as a Default Gateway. You would either add a return route for your SA/Network Connect IP Pool on your Core Switches, Firewall or Router. If needed, you can also add the route locally on the server. Based on what I know, you can't use the SA as a default gateway for outbound traffic (internal source). John
... View more
03-31-2011
04:39:PM
Hi, I came across the same issue and vaguely recall this being mentioned in the release notes as a known issue. I've been routing all the iPad traffic through the SA and back hauling the internet. Let me know if you come across a fix. Thanks. John
... View more
01-10-2011
05:30:PM
Hi, I would try a single IKE Gateway and two (2) AutoKey IKE (or VPN) entries. The VPN's will be used for the SA and should match the Cisco ACL on the other end. Are you setting up Policy or Route based VPN? John
... View more
10-04-2010
12:18:PM
Hi, Does anyone know what the maximum amount of active sync users is for the SA-2000? Also, is there a similar type of proxy for RCP over HTTPS (Macs)? Thank you. John
... View more
08-30-2010
07:17:PM
Does anyone have an update for Android support? I have a few Samsung Vibrants that just arrived and they're pretty slick. I see most of my users opting out of the iPhone and Droid for a Vibrant or similar Smartphone, especially factoring in the price. Thank you. John
... View more
07-16-2010
09:10:AM
Hi, Does anyone know if it's possible to monitor or report on Bookmark statistics? We have a complex approach that I'm looking to consolidate and would like to go into the meeting with supporting data. For example, all of our session use Network Connect, but only some user click on the Web Bookmarks and Terminal Session links. I'm looking for stats on Web Bookmark and Terminal Session usage. Thank you. -John
... View more
05-18-2010
07:10:PM
Hi, We have a couple of SA-2000's front-ending a Cisco VoIP solution. The softphone works great, along with the other unified VoIP features (including video). I would recommend reaching out to your account team or VAR for an eval unit. This is a great way to test your apps and VoIP before making a purchase. -John
... View more
04-28-2010
07:46:AM
Hi, I think that's because when your setup an RDP Terminal Session you're using the Juniper client and the same features aren't available. You can use Network Connect and your own RDP client. -John
... View more
01-08-2010
06:01:AM
Hi, You will need to either connect from the permitted IP and add additional IP's/subnets accordingly, or login via the console to fix the issue. -John
... View more
Latest Tags
No tags yet
© 2017 Pulse Secure, LLC. Use of this website assumes acceptance of our Legal Notices and Privacy Policy.
Pulse Secure has updated its Privacy Policy effective June 28, 2017.
