Letsencrypt.org is a free and automated Certificate Authority that makes it easy for organizations to secure websites. It can set up TLS certificates very easily, limited to one domain name (i.e., www.domain.com) and has the advantage that it supports both RSA and ECC certificates.   In this article, we show an example of how to configure Let’s Encrypt to work with Brocade vADC, including: Issue new certificates Automated renewal of certificates Install certificates and tools Use both RSA and ECC for performance and maximum compatibility Enable automatic OCSP stapling   Introduction Let’s Encrypt relies on the ACME protocol for Automated Certificate Management Environment, which was developed with automation in mind:   The software client connects to Let’s Encrypt to issue or renew a certificate An authorization/signature happens to verify you are the owner of the domain The certificate is generated and sent back to the software client   We'll use an open source client ( acme.sh ) to manage communications with Let’s Encrypt and we install a short script (letsencryptforvtm.sh) into Brocade vTM, which is used to issue and renew certificates. Then, we use the Brocade vTM alerting and scripting to trigger certificate renewal automatically through the open source script ( acme.sh ) to talk to Letsencrypt.org. The steps are as follows:   Install the open-source acme.sh client Install our action script (letsencryptforvtm.sh) Create a new action type for Brocade vTM Create a new alert for Brocade vTM Create a resource pool to manage responses from Letsencrypt.org Create a TrafficScript rule to manage responses from Letsencrypt.org       Installation procedure This installation procedure can be applied the same way if you're running the Brocade vTM appliance or the Brocade vTM software on your own Linux distribution.   Install acme.sh First, we need to download the open source component to manage the ACME protocol. Login as admin into your vTM through SSH, then run the following commands:   curl -LO https://raw.githubusercontent.com/Neilpang/acme.sh/master/acme.sh chmod +x acme.sh ./acme.sh --install --nocron   More options are available when installing acme.sh. For more information, please read  https://github.com/Neilpang/acme.sh/wiki/How-to-install .   Install letsencryptforvtm.sh Next, we need to download and install the short script that is used to issue and renew certificates and communicate with the acme.sh component.   Download the letsencryptforvtm.sh script (Available on github: https://github.com/bedis/letsencryptforvtm) Upload the script into the admin's home directory on Brocade vTM   This script can be run manually to issue a new certificate and insert into Brocade vTM, but we need to load it into the Brocade vTM Catalog, so that it can be called automatically to renew certificates.   Connect to the Brocade vTM Web UI, then navigate to Catalogs > Extra Files > Action Programs Click on the Choose File button and point to the letsencryptforvtm.sh script Click on the Upload Program button   Set up a new Action Now, we need to create a new action, which will be called when a certificate is about to expire.   Connect to the Web UI, then navigate to System > Alerting Click on the Manage Actions link Complete the "Create new action" form:  Name: letsencrypt_renewal  Type: Program     Click on Add action On the next page, in Additional Settings: Program: choose letsencryptforvtm.sh Click on the Updatebutton at the bottom of the page   Create a new Alert mapping In Brocade vTM, an alert maps an event to an action. In our case, we'll match the event "Certificate is about to expire" to the action we've created at the step before.   Connect to the Web UI, then browse System> Alerting In Select Event Type, choose SSL Certificate Expiry As an action, choose letsencrypt_renewal   Note: the SSL Certificate Expiry will match for all certificates configured into Brocade vTM, whether or not they were issued by Let’s Encrypt. It is possible to create a copy of this event, named SSL Certificate Expiry Lets Encrypt and match only the vservers where your Let’s Encrypt certificates are enabled.   Create a pool for the acme.sh script The purpose of this pool is to send ping back from Let’s Encrypt. While we are running acme.sh, we will need to make it listen for http requests on port 88. Note that once the certificate has been renewed or issued, then acme.sh will shutdown the port.   Connect to the Web UI, then browse Services > Pools Complete the Create a new pool form as below: Pool name: p_letsencrypt Nodes: 127.0.0.1:88 Monitor: Ping   Click on the Create Pool button   Create a new TrafficScript rule The purpose of this rule is to route ping back from letsencrypt.org to the pool which we created (p_letsencrypt) - which itself will route the request to the acme.sh script.   Connect to the Web UI, then browse Catalogs > Rules Complete the Create a new rule form with the following information: Name: route_to_acme.sh Check the Use TrafficScript Language
 option Click on the Create Rule button In the next page, complete the form as below: Notes: Route traffic related to acme.sh (letsencrypt) Rule: As shown here: $path = http.getPath(); if( string.containsI( $path, "acme-challenge" ) ) { pool.use("p_letsencrypt"); }
 Click on the Update button Later, you will add this rule to the vserver for your application     Complete your environment If you have not already set up your application with a vserver, you will need to create a vserver listening on port 80 on the IP address pointed by the domain for which you are issuing the certificate.   Now you can enable the TrafficScript rule route_to_acme.sh into the vserver which is managing the domain. This should be one of the first rules in the list.   Generate a new certificate In order to generate a new certificate for our application, we need to run the script to request a new certificate from Let’s Encrypt:   Connect to vTM using ssh Run the following command for an ECC certificate: ./letsencryptforvtm.sh --issue c_www.domain.com_ecc   Alternatively, run this command to request an RSA certificate: ./letsencryptforvtm.sh --issue c_www.domain.com_rsa   The new certificate is automatically inserted into Brocade vTM, which you can confirm by navigating to Catalogs > SSL. You can now navigate to your vserver, enable SSL offloading and select the new certificate.   Let’s Encrypt certificate chain The letsencryptforvtm.sh script takes care of this task for you. When inserting the certificate into Brocade vTM, the script uses the full chain, including the certificate for the domain and the required intermediaries.   Renew a Let’s Encrypt certificate When the certificate is due for renewal, our script should take care of the certificate renewal. Seven days before expiration, the alert mapping will run the letsencryptforvtm.sh script with the name of the certificate as an argument. If, for some reasons, Let’s Encrypt is not available at the first execution, Brocade vTM will attempt to call letsencryptforvtm.sh every hour until the certificate is renewed.   OCSP stapling Brocade vTM can use information available in the certificate to process OCSP stapling automatically. This feature works out of the box with Let’s Encrypt certificates.   All you need to do is to enable ssl_ocsp_stapling in your vserver when configuring SSL Decryption.     Using the TEST environment variable It is highly recommended to use the Let’s Encrypt test / staging environment during the installation phase. Otherwise, Let’s Encrypt may blacklist your domain if you generate too many certificates.   In order to use the test environment, edit letsencryptforvtm.sh script and search for the TEST variable: uncomment the TEST variable and re-upload the script into Catalogs > Extra Files > Actions.   Once the full procedure is validated and you want to move to production, simply comment out the TEST variable line and re-upload the script into Catalogs > Extra Files > Actions.   ... View more